Clutch, Transmission, Drive Chain, Sprockets
-
Seadog
- honda305.com Member
- Posts: 1272
- Joined: Thu Dec 25, 2014 9:54 am
- Location: Cape Cod, MA
Post
by Seadog » Sat Jan 31, 2015 2:42 pm
Messing about in my right case area today and noticed that the clutch actuator rod is bent, flattened a bit and scored on the portion inside the case. The detent for the ball bearing is also off center. Any idea how this happens? Before I buy a used replacement, is there any variation in early or late model rods that I should know about? Mine is approximately 9-11/16 inches long. The seal should also be replaced. Hopefully I can find one at the Honda dealer.
-
Attachments
-
- IMG_0424.JPG (164.18 KiB) Viewed 3290 times
-
- IMG_0422.JPG (177.45 KiB) Viewed 3290 times
-
G-Man
- honda305.com Member
- Posts: 5678
- Joined: Wed Mar 25, 2009 5:17 pm
- Location: Derby, UK
-
Contact:
Post
by G-Man » Sat Jan 31, 2015 3:40 pm
Maybe the drive chain came off and caught it......
G
'60 C77 '60 C72 '62 C72 Dream '63 CL72
'61 CB72 '64 CB77 '65 CB160
'66 Matchless 350 '67 CL77
'67 S90 '77 CB400F
-
Seadog
- honda305.com Member
- Posts: 1272
- Joined: Thu Dec 25, 2014 9:54 am
- Location: Cape Cod, MA
Post
by Seadog » Sat Jan 31, 2015 5:20 pm
G-Man wrote:Maybe the drive chain came off and caught it......
G
Thanks, G-Man. I guess anything is possible. The fact remains that I have to replace it and the seal. Will any CA77 clutch rod do, or must I find a specific one for my '64?
-
LOUD MOUSE
- honda305.com Member
- Posts: 7817
- Joined: Mon Aug 15, 2005 8:23 am
- Location: KERRVILLE, TEXAS
Post
by LOUD MOUSE » Sat Jan 31, 2015 5:27 pm
That part is the same for all 250/305 engines. ........lm
Seadog wrote:G-Man wrote:Maybe the drive chain came off and caught it......
G
Thanks, G-Man. I guess anything is possible. The fact remains that I have to replace it and the seal. Will any CA77 clutch rod do, or must I find a specific one for my '64?
-
Seadog
- honda305.com Member
- Posts: 1272
- Joined: Thu Dec 25, 2014 9:54 am
- Location: Cape Cod, MA
Post
by Seadog » Sat Jan 31, 2015 6:01 pm
LOUD MOUSE wrote:That part is the same for all 250/305 engines. ........lm
Thanks, LM. Now I can order one right away. Do you know if seal is still available?
-
LOUD MOUSE
- honda305.com Member
- Posts: 7817
- Joined: Mon Aug 15, 2005 8:23 am
- Location: KERRVILLE, TEXAS
Post
by LOUD MOUSE » Sat Jan 31, 2015 6:29 pm
I can supply both. ........lm
Seadog wrote:LOUD MOUSE wrote:That part is the same for all 250/305 engines. ........lm
Thanks, LM. Now I can order one right away. Do you know if seal is still available?
-
Seadog
- honda305.com Member
- Posts: 1272
- Joined: Thu Dec 25, 2014 9:54 am
- Location: Cape Cod, MA
Post
by Seadog » Sat Jan 31, 2015 6:35 pm
LOUD MOUSE wrote:I can supply both. ........lm
Great; email sent. Thanks
